Welcome to the
MIRATECH Solutions Guide

MIRATECH is the expert in providing fully integrated, proven exhaust compliance solutions for anyone using industrial engines in a Power Generation, Gas Compression and Mechanical Drives.

Review
Your Solution
Contact us for
Pricing & Details
continue

Tell us about your needs

Your selction did not return any results.
Please adjust your selection and try again.

Applications

  1. Gas Compression
  2. Power Generation
  3. Rail
  4. NESHAP Regulations
  5. Industrial
  6. Air Compression
  7. Liquids Pumping
  8. Bio-Gas
  9. Greenhouse CO2 Enrichment
  10. Industrial Marine

Engine Type

  1. Bi-Fuel Diesel and Natural Gas
  2. Diesel
  3. Natural Gas Lean Burn
  4. Natural Gas Rich Burn

Noise Control

  1. Yes
  2. No

Engine Size

  1. 20 to 200 hp
  2. 200 to 1350 hp
  3. 1350 to 10,000 hp
  4. 10,000 hp and above

Regulated Pollutants

  1. NOx
  2. NO2
  3. CO
  4. VOC (NMNEHC)
  5. HAP's
  6. Particulate Matter (PM)
RESET
 
continue

Submit your Request for Pricing and Details

Your Solution(s):

Contact Information

Error: Please complete form.


Thank You!
back
submit

EPA proposes rulemaking withdrawing “Once-In-Always-In” MACT policy.

August 1, 2019

On June 25, 2019, EPA released a pre-publication draft of a proposed rule allowing sources subject to Maximum Achievable Control Technology (MACT) standards under Section 112 of the Clean Air Act to voluntarily limit their emissions and avoid MACT according to a July 12, 2019 Environmental Law and Policy Monitor report.

The proposed rule, which formalizes and expands on a January 2018 guidance document issued by former EPA Assistant Administrator Bill Wehrum, would allow “major sources” of hazardous air pollutants (HAPs) otherwise subject to MACT standards to take an enforceable limit on HAPs and thus reclassify as “area sources.”

The rulemaking, branded by the Agency as “Major MACT to Area” (MM2A), would eliminate the Agency’s longstanding “once-in-always-in” policy, under which a facility that qualified as a major source of HAPs as of the “first substantive compliance date” of the applicable MACT standard was permanently subject to that standard, even if the source was later able to reduce its emissions below major source applicability thresholds.

The June 2019 regulatory proposal goes well beyond the Agency’s 2018 limited guidance on reclassification. The proposal identifies specific procedural steps a major source must take to reclassify to an area source and also identifies a process for an area source to revert back to major source status. EPA has also proposed to eliminate a requirement that any reclassification limits on HAP emissions be federally enforceable. The proposed rule contains criteria for effective HAP limits and EPA is seeking comment on these criteria, including whether HAP limits need to go through public notice and comment in order to be effective.

The MM2A proposal will not affect all industries in the same way. For some, like electric steam generating units, it will be of no benefit because sources in the category are subject to the same requirements regardless of their major or area source status. For many source categories, such as industrial boilers, EPA has adopted separate area source standards that would still apply. Thus, the implications of EPA’s proposal are likely to differ significantly from industry to industry, and even from source to source within a regulated category.

What this means to you
EPA has released a pre-publication draft of a proposed rulemaking branded by the Agency as “Major MACT to Area” that eliminates the Agency’s longstanding “once-in-always-in” policy, under which a facility that qualified as a major source of HAPs remains permanently subject to that standard, even if the source was later able to reduce its emissions below major source applicability thresholds.

MIRATECH can help
Contact MIRATECH for stationary engine emission control solutions.